Description
Product Description
Please call Glen for pricing: (905) 677-7995.
The STEEL-IT Polyurethane Coating System features a unique stainless steel leafing pigment and provides optimum weather-, abrasion-, and corrosion-resistance in general maintenance applications. The easy to apply system yields a hard, non-toxic, metallic finish that protects a multitude of metallic and non-metallic surfaces from ultraviolet rays, chemicals, oils, alkalis, food acids, water immersion, abrasion, and high-pressure washdowns.
Comprised of STEEL-IT Polyurethane #1002 applied over STEEL-IT Weathering Primer #2203, the system adheres to surfaces aggressively and is ideal for protecting structural steel and other metals. These single component coatings require no complicated mixing. Applied as they come from the can, they are air-dried and require no baking or heating. USDA-approved for use in the food processing and handling industry where incidental food contact may occur, STEEL-IT Polyurethane #1002 blends polyurethane resin with Type 316L stainless steel leafing pigment to produce a rugged, non-toxic, satiny metallic finish. STEEL-IT Primer #2203 combines a modified alkyd resin, selected silicates, and iron oxides with Type 316L leafing pigment to produce a long-lasting primer for structural steel and other metals requiring good rust-inhibiting qualities.
STEEL-IT Polyurethane #1002 and Primer #2203 is packaged in quarts and gallons. The #1002 Polyurethane is also available in handy aerosols for easy touch-ups and small jobs. Conventional or airless spraying is the preferred application method, however, they may also be applied easily by brush or roller.
Protects Steel from:
- Severe atmospheric environments
- Abrasion and impact
- Water (fresh and salt)
- High-pressure washdowns
Uses:
- Structural steel, food processing and packaging equipment
- Industrial equipment metal parts, air conditioning, refrigeration equipment, etc.
- Maintenance of trucks, auto parts, trailers
- Bridges, tanks, towers
System Recommendations:
Atmospheric Service in Light-Moderate Duty Areas. –
- 1 coat – STEEL-IT Alkyd Weathering Primer #2203
- 1 coat – STEEL-IT Polyurethane #1002 (within 4-24 hours of applying 2203 Primer)
Heavy Duty Service. –
- 1 coat – STEEL-IT Alkyd Weathering Primer #2203
- 2 coats – STEEL-IT Polyurethane #1002 (within 4-24 hours of applying 2203 Primer)
Surface Preparation:
General use in light atmospheric service. –
- Hand or power tool clean (SSPC-SP-2 and -3) after thoroughly removing all oils, salts and other contaminants.
Heavy Duty Service. –
- Sandblast to an SSPC-SP-6 (commercial blast)
- Anchor pattern should be cut and angular (1.5-2.0 mils deep).
Film Thickness:
General use. –
- 1 coat of #2203 (3.0 dry mils)
- 1 coat of #1002 (3.0 dry mils minimum)
Heavy Duty use. –
- 1 coat of #2203 (3.0 dry mils)
- 2 coats of #1002 (3.0 dry mils per coat)
- Film thickness on blasted surfaces should be measured up from the peaks of the anchor pattern.
Application:
- Conventional spray techniques use a Binks #62 Gun with a 68PB Air Cap and a 66 Fluid Tip or similar equipment.
- Airless applications use a DeVilbiss JGB-501 airless gun combination with a fluid tip orifice between 0.015 and 0.021. Pump ratio should be at least 28:1 or other compatible combinations.
Drying Time:
- #2203 Primer is a fast-drying material that is touch dry in 1 hour and should be recoated between 4 and 24 hours.
- #1002 is dry to touch in 2 hours and should be recoated within 24 hours.
- The finished system can be put into light service in 36 hours. The system will continue to cure to maximum hardness and protection for 5-10 days.
Coverage:
- #2203 Red Primer: theoretical coverage – 200 sq. ft./gallon at 3.0 dry mil.
- #1002 Finish: theoretical coverage – 150 sq. ft./gallon at 3.0 dry mil.
In practice, these values will be reduced by at least 25% by loss factors.
Thinning and Clean Up:
- Thinning is not recommended – only when mandatory.
- Air spray may require small amounts of mineral spirits, high flash naptha, xylene or toluene.
- Clean up with mineral spirits or xylene.
Limitations:
- Apply only when surface and ambient temperatures are above 40° F
- Relative humidity must be less than 86%.
- The surface temperature must be at least 5° F above dew point.
- Recommended for Surfaces where operating temperatures will not exceed 200° F.
STEEL-IT
Alkyd Primer #2203
- Color: Red | Sheen: Matte
- Total Solids: By weight: 65% | By volume: 38%
- Weight per Gallon: 11.8 lbs.
- Shelf Life: 1 year
STEEL-IT
Polyurethane Finish #1002
- Color: Metallic | Sheen: Low Gloss
- Total Solids: By weight: 49% | By volume: 28%
- Weight per Gallon: 9.4 lbs.
- Shelf Life: 1 year
MSDS (MATERIAL SAFETY DATA SHEET)
Reviews
There are no reviews yet.